Posted on

how to sterilize cannabis seeds for sprouting

This is the beauty of seeds—often, you can tell which plants or genetics will thrive right from the get-go. This will help you determine which plants you want to take cuttings from for clones or for breeding if you want to create a seed bank of your own.

If you’re ready for a more serious approach, make sure you have the space for a proper garden and pop the seeds to see what fruit they bear.

Females will have a round structure with long hairs—these hairs will develop into pistils, which will catch pollen in the air.

Step 4

Males will have round balls—these will develop into pollen sacs, which will release pollen into the air when mature.

As mentioned above, you can skip the processing of sexing weed plants by growing with feminized seeds or clones.

The main drawback to growing from seed is there is no guarantee as to what you’ll end up with—if you buy a regular pack of cannabis seeds, it will be a mix of males and females. You’ll need to sex them out (more below) to identify the males and get rid of them, because you don’t want your females producing seeds.

Feminized cannabis seeds will produce only female plants for getting buds, so there is no need to remove males or worry about female plants getting pollinated. Feminized seeds are produced by causing the monoecious condition in a female cannabis plant—the resulting seeds are nearly identical to the self-pollinated female parent, as only one set of genes is present.

Removing the ridge not only makes it easier for the seed to open, it helps with water absorption.

As you proceed through these steps, the risk of damaging your seeds past the point of recovery increases. Between each suggestion, give them a few days to a week to germinate. Allow the outside to dry each time to prevent rot. Do not try all or multiple techniques at once.

The seed’s shell is made up of two pieces, with a seam going all around. The side that’s raised more than the other is the ridge. A hardened ridge can make it difficult for the seed to open. To remove the ridge, run a sharp blade along the ridge on both sides. Handle gently and it should come off without damaging the inside of the seed.

3. REMOVE THE RIDGE

To scarify your seeds, line a matchbox or other small container with sandpaper. Drop the seeds inside, shake vigorously for 30–60 seconds, then remove. You may not notice much of a difference, but the small micro-abrasions are sometimes enough to let water breach the shell and trigger germination.

In a life or death situation, surgery may be the only option. Meaning—only do this if nothing else has worked because this technique ruins as many seeds as it saves.

The older a cannabis seed gets, the harder it is to pop. But hard doesn’t mean impossible. If you’ve been saving your seeds for a rainy day and it finally started pouring, these tips could help you get most, if not all, of your old beans to germinate.

As cannabis seeds age, their protective outer shell hardens and prevents water from passing through. Unless the tiny, dormant embryo that lives inside the shell detects moisture, it doesn’t know that the conditions are right to sprout. As a first step, pre-soak your old cannabis seeds for about 12 hours to see if that does the trick.

Growing your own weed is fairly easy, as explained in our article ‘All You Need For Growing Weed At Home‘. The hardest part for some growers though, is germinating their newly bought cannabis seeds. After all, the vulnerable seedlings are easily damaged. However, making sure your cannabis seeds survive germination is essential for a successful grow. In this blog, we highlight three tested methods that let anyone germinate cannabis seeds with minimal effort.

For this method, simply prepare your medium by moisturizing it, again, without soaking the soil completely. Then take your flower pots and use your finger to make a small hole about 10-15mm deep in the top layer to put the seed in. Cover the seed up loosely and top it off with a little water. Be careful not to give too much at once though! A stream of water can cause the seed to travel further down the pot where it’s too moist – and too deep to travel back up again.

How To Germinate Cannabis Seeds, Step 1: Get Good Genetics

So there you have it: whichever method you chose, germination should now be underway. Remember that even the best seed banks work with organic, natural materials, so 100% germination rates can never be guaranteed. If you get your technique right, though, most or all of your seeds should germinate according to plan. Once your seeds have become seedlings, the next steps of your grow await. There’s a lot of choices to make from here to harvest time: indoor or outdoor, which spot to pick, what nutrients to use, and so on. Keep an eye on our expanding grow blog collection if you want to learn more!

Germination is actually a process where you activate a dry seed that is in a ‘sleeping state’. By adding water to the seed, a small root that is inside the seed-shell will want to come out in search for more water. This will make it develop into a big taproot that’ll serve as an anchor for the plant and from which more roots will sprout. Read more about root-development in this article: ‘Clones vs. Seeds: What Grows The Best Cannabis?‘

Most plugs are dry blocks of (usually) coco fibre. Peat plugs are an interesting alternative, as these contain some initial nutrients to help the seedling along. After fully absorbing about 500ml of moisture, or 250ml of a root booster and another 250ml water, they slowly turn into a moist, soil-like plug. Grow plugs usually have a premade hole in which to place the seed. After sticking the seed in the top of the plug, cover it lightly with a little leftover plug fibre. It takes a few days at maximum before you see the first heads pop. As soon as the roots grow out of the bottom or the side of the plug, you can stick the entire plug, complete with its seedling, into your intended medium. These plugs make germination and the initial transplant a piece of cake.